Motor Control Stepper Motor

Part-No. / Function Interface VSUPPLY IPEAK P(Motor) peak RDSON Package Comment
E520.03 (*Driver IC)
8x Low-Side for 2 Stepper Motors with Stall Detection
  • SPI-compatible (3.3/5V)

3V to 25V (42V)

8x 350mA

≈8x 8.75W

1.5Ω

QFN20L5
QFN32L5
SOIC20

  • Stall detection for stepper motors (E520.03) suitable for Full Step, Half Step, Wave Drive
  • 245Hz LED mode
  • 25kHz relay mode
  • 25kHz linear PWM
  • TJunc peak = +150°C

BLDC Motor BLDC Motor Driver

Part-No. / Function Interface VSUPPLY IPEAK IMAX DC P(Motor) peak RDSON Package Comment
E523.01, E523.11 (*SBC)
B6 Bridge FET Driver (LIN/PWM Interface)
  • LIN 2.x (1.3 comp.),
    SAE-J2602(only E523.01) or
  • PWM bidirectional
  • LIN Flash update

7V to 28V (5V to 42V)

6x ±400mA

6x ±75mA

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN44L7
QSOP44

  • Voltage Regulator (3.3V/5V) selectable
  • Precise deadtime generation
  • Watchdog/Diagnostics
  • TJunc peak = +170°C
  • Demo software on request (sensorless sinus)
E523.10 (*SoC)
BLDC-Motor Driver with Cold-Crank Capability
  • PWM bidirectional
  • SPI for configuration

7V to 28V (4.5V to 42V)

6x +400mA
6x -600mA

6x ±75mA

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN44L7

  • Voltage Regulator (3.3V/5V) selectable
  • Precise deadtime generation
  • Watchdog/Diagnostics
  • TJunc peak = +170°C
E523.50 (*SBC)
72V Brushless Motor Gate Driver
  • PWM for motor control
  • Diagnostic PINs

12V to 72V (7V to 76V)

6x ±200mA

6x ±50mA

≈1.5kW (external FETs)

10Ω (HS)
5Ω (LS)

QFN36L7

  • Usable for 24/48V automotive Board Net
  • DC/DC converter for gate supply
  • 3.3V/20mA supply for external µC
  • TJunc peak = +150°C

Motor Control DC Motor

Part-No. / Function Interface VSUPPLY IPEAK IMAX DC P(Motor) max RDSON Package Comment
E523.03, E523.04, E523.13, E523.14 (*SBC)
DC Motor LS FET Driver (LIN/PWM Interface)
  • LIN 2.x (1.3) or
    SAE-J2602
    (only E523.03/13) or
    PWM bidirectional
  • SPI for configuration

7V to 28V (5V to 42V)

±400mA

±75mA

≈1.5kW
(external FETs)
≈1.3W
(direct drive)

8Ω (HS)

4Ω (LS)

QFN20L4
QFN32L5 (with high voltage spacer)

  • Voltage Regulator
    E523.03/13: 5V | E523.04/14: 3.3V
  • Watchdog/Diagnostics
  • Fast LIN Flash update
  • TJunc peak = +170°C
E523.05 (*SoC / *Plug & Play)
DC 2x Half-Bridge Controller with 16bit CPU (LIN / PWM Interface)
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for configuration
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6x ±400mA

6x ±75mA

≈1.5kW

(external FETs)

≈1.3W

(direct drive)

8Ω (HS)

4Ω (LS)

QFN48L7

  • For new designs E523.06 is recommended
  • 16bit/48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack software update via LIN
  • Charge Pump Driver included
  • TJunc peak = +125°C
    (Contact supplier for higher temperature)
E523.06 (*SoC)
Field-Oriented DC Motor Controller with 16 Bit CPU
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for configuration
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6x ±400mA

6x ±75mA

≈1.5kW (external FETs)
≈1.3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7

  • 16bit/48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack software update via LIN
  • Charge Pump Driver included
  • TJunc peak = +125°C
    (Contact supplier for higher temperature)
E523.30 (*SoC)
2x Full Bridge Controller (LIN / PWM Interface)
  • LIN 2.x (1.3) or SAE-J2602 or PWM bidirectional
  • LIN auto-addressing (slave mode position detection)
  • LIN Flash update for EoL and Service
  • JTAG

7V to 20V (5.5V to 42V)

-

2x ±75mA

≈25W
(per Motor)

225mΩ (HS)
275mΩ (LS)

QFN32L6

  • Drives 1 or 2 DC motors
  • 8bit CPU, 8k FLASH, 64Byte E2PROM
  • Current chopper motor control
  • Supply and read-out of up to 3, potentiometers or sensors
  • GPIO-pins
  • TJunc peak = +170°C
    (contact supplier for higher temperatures)
  • (*Plug & Play) - Demosoftware on request
E910.72 (*Driver IC)
6x Half-Bridge DC Motor with sensorless positioning
  • SPI™ for configuration

6V to 19V (40V)

-

540mA

≈7W
(1 Motor Mode)

1.25Ω

QFN32L5

  • Sensorless motor positioning
  • 3 independent pulse detectors
  • Excellent positioning performance
  • Drives 3 or 5 DC actuators
  • TJunc peak = +150°C

BLDC Motor BLDC Motor Controller

Part-No. / Function Interface VSUPPLY IPEAK IMAX DC P(Motor) peak RDSON Package Comment
E523.05 (*SoC)
BLDC Motor Controller with 16bit CPU (LIN/PWM Interface)
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for expansion
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6x ±400mA

6x ±75mA

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7

  • For new designs E523.06 is recommended
  • 16bit / 48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack, software update via LIN
  • Software support on request
  • TJunc peak = +125°C (contact supplier for higher temperature)
E523.06 (*SoC)
Field-Oriented BLDC Motor Controller with 16 Bit CPU
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for expansion
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6x ±400mA

6x ±75mA

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7
LQFP48L7EP

  • 16bit / 48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack, software update via LIN
  • Software support on request
  • TJunc peak = +125°C (contact supplier for higher temperature)
  • *Plug & Play:
    Demosoftware for
    - sensorless HVAC fan,
       engine cooling fan
    - field oriented control (FOC)
       for pumps
E523.52 (*SoC)
72V Brushless Motor Gate Driver with 16bit CPU
  • LIN Interface with external LIN transceiver
  • PWM Interface with external components
  • SPI for user expansion
  • LIN Flash update
  • JTAG

12V to 72V (7V to 76V)

6x ±500mA

6x ±50mA

≈1.5kW (external FETs)

10Ω (HS)
5Ω (LS)

QFN36L7

  • 16bit / 48 MHz CPU assisted by 2 powerful co-processors
  • Library  ROM for LIN-stack, software update via LIN (software support on request)
  • Standard HVAC fan firmware on request
  • TJunc peak = +125°C  (contact supplier for higher temperature)
  • *Plug & Play: Demosoftware on request