Motor Control Stepper Motor

Part-No. / Function Interface Output VSUPPLY IPEAK P(Motor) peak RDSON Package Comment
E520.03 (*Driver IC)
8x Low-Side for 2 Stepper Motors with Stall Detection
  • SPI-compatible (3.3/5V)

8 channel

3V to 25V (42V)

≈8x 8.75W

1.5Ω

QFN32L5
SOIC20

  • Stall detection for stepper motors suitable for Full Step, Half Step, Wave Drive
  • 245Hz LED mode
  • 25kHz relay mode
  • 25kHz linear PWM
  • TJunc peak = +150°C
E523.62 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD
  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 600mA/ch

≈9W

1.6Ω (HS)
3.0Ω (LS)

TSSOP16-EP

  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
E523.63 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD
  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 1000mA/ch

≈15W

0,6Ω (HS)
1,0Ω (LS)

TSSOP16-EP

  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 

BLDC Motor BLDC Motor Driver

Part-No. / Function Interface VSUPPLY IPEAK P(Motor) peak RDSON Package Comment
E523.01 (*SBC)
B6 Bridge FET Driver (LIN/PWM Interface)
  • LIN 2.x (1.3 comp.),
    SAE-J2602(only E523.01) or
  • PWM bidirectional
  • LIN Flash update

7V to 28V (5V to 42V)

6 channel

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN44L7
QSOP44

  • Voltage Regulator (3.3V/5V) selectable
  • Precise deadtime generation
  • Watchdog/Diagnostics
  • TJunc peak = +170°C
  • Demo software on request (sensorless sinus)
E523.10 (*SoC)
BLDC-Motor Driver with Cold-Crank Capability
  • PWM bidirectional
  • SPI for configuration

7V to 28V (4.5V to 42V)

6 channel

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN44L7

  • Voltage Regulator (3.3V/5V) selectable
  • Precise deadtime generation
  • Watchdog/Diagnostics
  • TJunc peak = +170°C
E523.50 (*SBC)
72V Brushless Motor Gate Driver
  • PWM for motor control
  • Diagnostic PINs

12V to 72V (7V to 76V)

6 channel

≈1.5kW (external FETs)

10Ω (HS)
5Ω (LS)

QFN36L7

  • Usable for 24/48V automotive Board Net
  • DC/DC converter for gate supply
  • 3.3V/20mA supply for external µC
  • TJunc peak = +150°C

Motor Control DC Motor

Part-No. / Function Interface VSUPPLY IPEAK P(Motor) max RDSON Package Comment
E523.05 (*SoC / *Plug & Play)
DC 2x Half-Bridge Controller with 16bit CPU (LIN / PWM Interface)
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for configuration
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6 channel

≈1.5kW
(external FETs)

≈3W
(direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7

  • 16bit/48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack software update via LIN
  • Charge Pump Driver included
  • TJunc peak = +125°C
    (Contact supplier for higher temperature)
E523.06 (*SoC)
Field-Oriented DC Motor Controller with 16 Bit CPU
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for configuration
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6x ±400mA

≈1.5kW (external FETs)
≈1.3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7

  • 16bit/48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack software update via LIN
  • Charge Pump Driver included
  • TJunc peak = +125°C
    (Contact supplier for higher temperature)
E523.26 (*SoC)
DC Motor Driver with 16kB Flash
  • LIN 2.x (1.3) or
    SAE-J2602
  • SPI for configuration

5V to 20V
(5V to 40V)

1 channel

≈1.5kW
(external FETs)
≈1.3W
(direct drive)

8Ω (HS)
8Ω (LS)

QFN32L6

  • Includes μC, memory, interfaces, high side gate driver, supply and measurement functions
  • TJunc peak = +150°C
E523.30 (*SoC)
2x Full Bridge Controller (LIN / PWM Interface)
  • LIN 2.x (1.3) or SAE-J2602 or PWM bidirectional
  • LIN auto-addressing (slave mode position detection)
  • LIN Flash update for EoL and Service
  • JTAG

7V to 20V (5.5V to 42V)

2 channel

≈25W
(per Motor)

225mΩ (HS)
275mΩ (LS)

QFN32L6

  • Drives 1 or 2 DC motors
  • 8bit CPU, 8k FLASH, 64Byte E2PROM
  • Current chopper motor control
  • Supply and read-out of up to 3, potentiometers or sensors
  • GPIO-pins
  • TJunc peak = +170°C
    (contact supplier for higher temperatures)
  • (*Plug & Play) - Demosoftware on request
E523.62 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD
  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 600mA/ch

≈9W

1.6Ω (HS)
3.0Ω (LS)

TSSOP16-EP

  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
E523.63 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD
  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 1000mA/ch

≈15W

0,6Ω (HS)
1,0Ω (LS)

TSSOP16-EP

  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
E910.72 (*Driver IC)
6x Half-Bridge DC Motor with sensorless positioning
  • SPI™ for configuration

6V to 19V (40V)

-

≈7W
(1 Motor Mode)

1.25Ω

QFN32L5

  • Sensorless motor positioning
  • 3 independent pulse detectors
  • Excellent positioning performance
  • Drives 3 or 5 DC actuators
  • TJunc peak = +150°C

BLDC Motor BLDC Motor Controller

Part-No. / Function Interface VSUPPLY IPEAK P(Motor) peak RDSON Package Comment
E523.05 (*SoC)
BLDC Motor Controller with 16bit CPU (LIN/PWM Interface)
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for expansion
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6 channel

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7

  • For new designs E523.06 is recommended
  • 16bit / 48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack, software update via LIN
  • Software support on request
  • TJunc peak = +125°C (contact supplier for higher temperature)
E523.06 (*SoC)
Field-Oriented BLDC Motor Controller with 16 Bit CPU
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for expansion
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6 channel

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7
LQFP48L7EP

  • 16bit / 48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack, software update via LIN
  • Software support on request
  • TJunc peak = +125°C (contact supplier for higher temperature)
  • Plug & Play:
    Demosoftware for
    - sensorless HVAC fan,
      engine cooling fan
    - field oriented control (FOC)
      for pumps
E523.52 (*SoC)
72V Brushless Motor Gate Driver with 16bit CPU
  • LIN Interface with external LIN transceiver
  • PWM Interface with external components
  • SPI for user expansion
  • LIN Flash update
  • JTAG

12V to 72V (7V to 76V)

6 channel

≈1.5kW (external FETs)

10Ω (HS)
5Ω (LS)

QFN36L7

  • Usable for 24/48V automotive Board Net
  • 16bit/48 MHz CPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack software update via LIN (software support on request)
  • TJunc peak = +150°C
E523.62 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD
  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 600mA/ch

≈9W

1.6Ω (HS)
3.0Ω (LS)

TSSOP16-EP

  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
E523.63 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD
  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 1000mA/ch

≈15W

0,6Ω (HS)
1,0Ω (LS)

TSSOP16-EP

  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
Show cookie popup